This is Why Your GE Dishwasher Won’t Start, Just Beeps!
Does your GE washer beep and not respond when you turn it on? If yes, it means there is an issue with your dishwasher.
The sounds from the dishwasher are its way of communicating issues to you. However, it can be frustrating if it doesn’t display error codes.
It is also aggravating if the machine does not respond to its functions. If you want to determine its cause and also find a solution to the problem, you’ve come to the right place.
If your GE dishwasher beeps and refuses to start when you turn it on, it means your door latch is still open. It also makes these sounds after a power surge. To stop the beeping sound, close your washer door properly. However, if this solution does not fix the issue, you should keep troubleshooting to find the cause and its fix.
In this article, I will walk you through the causes of this problem. With the guide below, you can fix some of the issues without the help of an expert.
You will also be able to identify the different types of beeps and their meaning.
Why Is My GE Dishwasher Beeping but Not Starting?
If your GE dishwasher keeps beeping continuously and does not start, it is mainly because your door latch is open during a cycle.
The dishwasher beeps to notify you of an irregularity. The beeping sound comes with blinking lights which have different meanings depending on their consistency.
The beeping sound could also result from a water pressure issue, a power surge, or a fault with the pressure switch.
Nonetheless, if you cannot identify the cause of the sound, you can consult your appliance user manual for detailed information on the cause of the issue.
Before trying other fixes or further troubleshooting, reset the dishwasher by pressing and holding the Start button for about ten minutes. Wait till the machine resets, and it’s good to go.
If the issue persists after trying this method, disconnect your dishwasher from its power source and let it discharge for two minutes before turning it on.
Below are some of the varying types of error beeps with their different meanings:
#1. 30 Seconds Beep
This type of beep is common and occurs in GE dishwashers. If the timing of the beep is 30 minutes, it indicates that your dishwasher door latch is open during a wash cycle.
When you open the washer door, it beeps to signify an open door, so naturally, it also occurs when you try to start a cycle without latching the machine door properly.
You can quickly correct this issue by pausing the wash cycle, locking the washer door, and resuming the cycle.
#2. Beep Triggered by Power Surge
Once there is a sudden power outage while the dishwasher is on can cause the dishwasher to beep after you restart it.
This power outage could come with a spike that can damage your washer’s interior. In this case, however, you might need additional repairs for the damages.
However, if there was no damage to the dishwasher component, you can press and hold the Start button for a few minutes to reset the washer.
The reset will consequently stop the beeping and restore your dishwasher.
#3. Start Buttons Blink While Washer Beeps
If your washer beeps and blinks simultaneously for about 60 to 90 seconds, the washer resets itself after you turn it off.
Turn on your dishwasher and initiate a new cycle after it stops beeping and blinking. Also, observe the cycle and ensure it is running smoothly.
#4. Beeps Due to Rinse Aid issues
Using the right amount of rinse aid for your wash cycle is also necessary to sustain your appliance’s life.
When you use excessive rinse aid during a wash cycle, it triggers the beeping sound.
Therefore, browse through your user manual to get an idea of the amount of rinse aid you need for your wash cycle.
#5. Beeps Triggered by Pressure Switch
Once your dishwasher detects any problem with your pressure components, like the flow meter and sensor, it will start beeping.
The pressure switch is a sensitive part of the dishwasher and can be challenging to diagnose. If this issue is the cause of the beeping sound, contact an expert.
#6. Anti-flood Beep
If your machine has an anti-flood device or a detector that senses excess water flow in your dishwasher, it will beep when the sensor activates.
Once it starts beeping, it will trigger your washer to stop functioning. To stop the beeps, use a dry sponge or cloth to drain the water if your washer is an integrated model.
However, if your dishwasher is a freelance model, you can slightly tilt the appliance to drain the excess water.
#7. Different Types of Dishwasher Beeps and Their Meaning
| Beep Type | Meaning |
|---|---|
| 30-second beep | The dishwasher door latch is open during a cycle. |
| Beeping triggered by pressure switch | An issue with the pressure components. |
| Anti-flood beep | The dishwasher anti-flood sensor is activated. |
| Start buttons | You recently turned the washer off. |
| Power surge beep | Beep due to a recent power outage. |
| Rinse aid beep | You added excess rinse aid to the machine during a wash cycle. |
| Beep due to mechanical issues | There is a faulty component in the washer. |
How Do I Fix a GE Dishwasher That Won’t Start but Just Beeps?
If your GE dishwasher does not start but beeps continuously, you can check if your door latch is open and shut the latch tightly. If the latch is not open, you can reset it.
If the door is not the problem, it might be an issue with the door sensor. You can use a multimeter to test the sensors for continuity. If it is faulty, replace the sensor.
The GE dishwasher will not operate if your door is open. Instead, it will send warnings in the form of beeps.
Also, if the latch is loose, your dishwasher might shut down. In this case, you might have to replace the latch.
If the issue persists after trying the solutions, try the solutions below to get your dishwasher back to normal:
#1. Click the Reset Button
If the issue persists after you try closing the door latch or replacing some of its components, the next best thing to do is reset the washer.
Rebooting the GE dishwasher will return it to its default setting and stop the beeping.
#2. Disconnect the Dishwasher
If resetting the washer does not stop the beeping, you might have to troubleshoot the issue by unplugging the washer from its power source.
This method will undoubtedly help clear the beeping sound and tell you if there is an underlying problem with the washer.
How Do You Reset a GE Dishwasher That Won’t Start?
If your GE dishwasher doesn’t start, there are two ways you can fix the issue–by rebooting the dishwasher and performing a factory reset on the washer.
Try the reset options below to get your GE dishwasher up and running:
#1. Reboot the Dishwasher
To reset a GE dishwasher that will not start, click the start button to stop the cycle. If your machine is a front loader, press the reset button.
However, if it is a top-loader, open the lid before clicking the start button, then close it. Wait for about two minutes to allow the water to drain out.
While waiting, you might notice blinking lights, which indicates that your washer is resetting. Ensure the blinking has stopped before turning on the machine.
Open the washer door again and load it if you need to. Start a wash cycle by clicking the Start button again and close the door latch firmly.
#2. Factory Reset
Factory resetting your GE washer goes beyond turning on a start or reset button.
Unlike the factory reset method, rebooting the washer erases the issues like beeping sounds or error code display.
Factory reset involves removing the residual electrical energy in the washer while clearing its settings.
To perform the factory reset, disconnect your washer from its power source. Next, wait about five to ten minutes before reconnecting the dishwasher to its power outlet.
How Do You Do a Hard Reset on a GE Dishwasher?
You can perform a hard reset on your GE dishwasher by turning off the circuit breaker connected to the washer.
Though a hard reset will help you clear the error, it should be your last resort when troubleshooting your washer.
To hard reset your GE dishwasher:
- Disconnect the washer from the power outlet. This action will reset the appliance and clear some error messages in the washer.
- If you cannot access the power source of the washer, you can turn it off from the primary power source.
- Locate the fuse box that shares a connection with the dishwasher and turn the circuit off.
- Disconnect only the circuit connected to your dishwasher unit and not other parts of your home.
- Wait for about five to ten minutes before you turn on the circuit.
- Though your GE manual may suggest turning it off for about 30 seconds, your washer might need a longer time.
- Allow your dishwasher to hard reset for about 10 minutes before restoring its power.
Conclusion
There is no perfect time for your dishwasher to detect errors and notify you. Therefore, when you hear a beeping sound from your washer, attend to it immediately.
Try latching the door firmly to see if the beeps will stop. If it persists after trying other solutions in the article above, contact an expert to inspect the washer.
