Whirlpool Gold Refrigerator Front Panel Not Working!
A whirlpool gold refrigerator has a front panel to give you easy control over the functions of the refrigerator.
Sometimes when you need to use your refrigerator, the control panel might refuse to work, which can get annoying.
When your refrigerator’s control panel refuses to work, it might be due to no power flowing through or accidentally switching it to modes such as showroom mode or Sabbath Mode. It might as well be because it has gotten faulty and requires repair.
Why Is My Whirlpool Gold Refrigerator Front Panel Not Working?
There are a few reasons why your whirlpool gold refrigerator front panel would not work. If it’s because the front panel has gotten faulty, you’d get blinking or buzzing sounds to notify you.
If a malfunction is not the case, here are a few possible reasons.
#1. Power Outage
The control panel stops working when no power flows through the refrigerator. There’s an indicator on the fridge to show when the power supply has been cut off.
#2. Showroom Mode or Demo Mode
The showroom or demo mode is a mode on refrigerators that allows you to deactivate some controls. This command restricts the control panel from optimum responsiveness.
If your control panel is not working, you probably unintentionally switch to this mode.
#3. Sabbath Mode
The Sabbath Mode is a mode on some refrigerators for those who need to turn off their appliances before going for religious activities. When the Sabbath Mode is turned on, certain controls are disabled.
Can You Fix The Front Panel Of A Whirlpool Gold Refrigerator?
Yes, you can fix the front panel of a whirlpool gold refrigerator. When your refrigerator’s front panel starts to malfunction, you might consider taking it out for repair, but sometimes, it just requires a simple troubleshooting method.
When your control panel starts to malfunction, the problems you’d most likely encounter are:
- Poor ice production
- Your refrigerator refusing to cool
- The motor or fan in the refrigerator runs too fast
- The water dispenser is not properly working
- The refrigerator is loud and noisy
Here’s how to fix any of the above problems:
#1. Poor ice production
If your ice maker isn’t producing as much ice, check if you didn’t accidentally turn it off. If that’s not the case, then here are troubleshooting methods to try out:
#1. Check the water line
Ensure that your ice maker is connected to a proper water supply. The ice maker will not be able to make enough ice if it isn’t getting as much water.
You can check the water line connection at the back of the fridge.
#2. Open The Water Valve Fully
Make sure the water valve is fully open by turning it counterclockwise. You can find the water shut-off valve under the sink, the cabinet next to the refrigerator, or the wall behind the fridge.
#3. Remove the water filter.
Remove the water filter and wait a while (a few hours or a day). If the water volume improves, your water filter must have been clogged.
You should consider reinstalling or changing the water filter.
#2. Your Refrigerator Refusing To Cool
The first thing to do is check if the power is out or if there’s too much food in the refrigerator.
If that’s the case, it’ll take a while (about 24 hours) to return to normal. If not, here are troubleshooting methods to try out:
#1. Check If The Settings Are Correct
Ensure that your settings are right. Some refrigerators require you to turn on a cooling setting before the refrigerator starts to get cold. Check your user care guide to learn how this setting works.
#2. Check For Blocked Air Vents
If the air vents in the freezer or fridge are blocked, there won’t be proper airflow to ensure proper temperature. Make sure no food items are blocking your vents.
#3. Clean The Condenser Coils
If your environment gets dusty or greasy, you should clean the condenser every 2 to 3 months.
#3. The Refrigerator Too Noisy
The refrigerator has normal operating sounds. When the fridge starts to get faulty, it starts to produce weird noises.
Check out the refrigerator noises guide to differentiate normal operating sounds from noises and how to fix them.
#4. Water Dispenser Not Properly Working
If your water dispenser is not working properly (dispensing water slowly or dispensing cloud water), here are troubleshooting methods to fix it.
#1. Check The Water Filter
A clogged water filter will slow down the water dispensing flow. If your water filter is clogged, remove it, change it and then reinstall.
#2. Flush The Water System
It is necessary to flush the water system every time you change the filter or install a new water line.
If you don’t flush the water system from time to time, the air might cause leakage or slow dispensing of water.
#3. Check The Water Pressure
Under normal circumstances, your water pressure should be between 30 and 120psi.
If it’s anything lower than that, your water filter must be clogged, or the cause might be a reverse osmosis system.
How Do You Reset The Front Panel on A Whirlpool Gold Refrigerator?
When the front panel of your whirlpool gold refrigerator develops a fault, it starts beeping or flashing lights to notify you. One way to fix the front panel is by resetting your whirlpool refrigerator.
Here are steps on how to reset your whirlpool gold refrigerator.
Step 1
The first step is to unplug your refrigerator. Unplugging your refrigerator from the power socket will permit it to reboot, refresh and fix errors, glitches and faults.
If you cannot reach the power cord because you have an in-built cabinet, you can switch off the power from the circuit breaker.
Ensure you don’t have any food in your refrigerator when attempting to reset it to prevent wastage.
Step 2
After unplugging your refrigerator from the power cord or circuit breaker, wait for about five to ten minutes.
After initially unplugging your refrigerator, some amount of power supply would still run through the appliance.
You’d have to wait for some time for all the power to run out completely. If you don’t wait, the reset process will not turn out as planned, and some faults will remain.
Step 3
After all the power has run out, the step is to plug the power cord back in or switch on the power from the circuit breaker. This step completes the back resetting process.
When power starts running through the whirlpool gold refrigerator, you’d hear a buzzing sound to show that the fan and motor are running. The refrigerator would light up when you open the door.
Step 4
Now that your whirlpool gold refrigerator has started running, the next thing to do is to check if the cooling function has been reactivated. The cooling function usually reactivates automatically, but sometimes it doesn’t.
If the cooling function didn’t reactivate, here’s how to do it manually.
- Look for the control panel. The control panel is usually at the door or inside the unit.
- Press the lock and filter buttons at the same time
- Hold onto the buttons for about three seconds
- Release your hold on the buttons.
You’ll know the process is successful when the refrigerator releases cool air from its vents.
Step 5
The next thing to do is to check your control panel’s functionality. To know if your control panel is still malfunctioning, you’d notice the following:
- Flashing lights
- Your whirlpool gold refrigerator starts creating buzzing sounds
- Some of the buttons on your whirlpool gold refrigerator won’t respond
Some refrigerators have control panels inside the unit and sometimes at the door, depending on the model.
| Refrigerator Model | Where To Find The Control Panel |
|---|---|
| JC2225GEKB | Inside the fridge’s unit |
| GZ2626GEKW | Inside the fridge’s unit |
| MBL1956KES4 | Inside the fridge’s unit |
| ABB2527DEW | Inside the fridge’s unit |
| KBRS19KTBL3 | Inside the fridge’s unit |
| GX5FHTXTS00 | Inside the fridge’s unit |
If your control panel is still malfunctioning, consider contacting whirlpool support.
Before you contact whirlpool support, ensure you’re ready to do the following:
- Warranty information
- Order number (optional)
- Whirlpool refrigerator model
- Whirlpool refrigerator serial number
You can find the details of your refrigerator’s model and serial number on the left or right side of the unit.
Summary
The refrigerator control panel gives you access control to the fridge’s function, so when it stops working, you might get annoyed.
When the control panel gets faulty, you’d see blinking lights and notice some problems such as annoying noises, slow running of the water dispenser, poor ice production, etc.
There are a few reasons why your control panel would be faulty, and you can easily fix them on your own or take them out for repairs.
