5 Reasons Your Whirlpool Washer Beeps And Won’t Start!
Washers are one of the home appliances you can rely on to do your laundry on time. The various available brands make each unique feature easier to choose from.
However, one common feature of washing machines is beeping sounds. This sound is primarily an indication of a minor problem.
If you own a Whirlpool washer, you might become concerned when it beeps and won’t start. Nonetheless, it is nothing to worry about, and you can quickly fix it.
Whirlpool washers might beep and refuse to start for different reasons. First, it may indicate that you must shut the door correctly or that something obstructs it. Another reason has clogs in the drain hole or lint build-up. However, when you fix the problem, the beeping stops and can function correctly.
Why Does My Whirlpool Washer Beep and Doesn’t Start?
There are various reasons why your Whirlpool washer would beep and not start. The beeping is there to tell you that something is incorrect.
It indicates that you need to update your washer’s maintenance and repairs. On the other hand, if you clean the drain regularly or lint glass, you might not experience this.
Nonetheless, here are why your Whirlpool washer would beep and not start.
#1. Clogged Drain
Clogs are not foreign to washing machines and other electric appliances that deal with water and particles.
Undoubtedly, you must encounter problems that arise from them if you own these appliances. For example, your Whirlpool washer will beep and not start if the drain is clogged.
As you know, the wash cycle starts when water enters the clothes’ tub. After that, the soapy water goes through the drain, and clean water re-enters to rinse the clothes.
Unfortunately, if the drain is clogged, the water will take longer to drain, leading to a prolonged cycle.
In severe cases where the wash cycle is too long, the washing machine would display an error code. This code indicates a problem with the drain, and the process cannot continue.
If your Whirlpool washer cannot drain correctly and on time, it displays F21 as an error code. The display screen comes on, and F21 keeps blinking for you to see.
#2. Partially-closed Door
This fault is one of the most common problems that make a Whirlpool washer beep and not start.
For example, if you do not close the door of your front-load or top-load washer, it will beep and refuse to start.
It might be frustrating, especially if you are in a hurry and have little time to spare. Moreso, it might happen because of your poor attempt to close the door correctly.
However, a piece of clothing might obstruct the door from closing correctly. Consequently, you must pay attention when closing your Whirlpool washer’s door.
#3. Lint Build-up
Lints are scraps from fabric that usually come off during washing. Although it does not shed large quantities, it can build up over time and obstruct the vent.
If it clogs the vent, the washer will have insufficient air, leading to problems. Most of these problems come with error codes and loud beeps.
Consequently, your washing machine will be unable to begin its wash cycle. There might be a little confusion concerning lint and clogs in the drain.
But, of course, here are a few highlighted differences between the two in the table below.
| Lint | Clogs |
|---|---|
| Stores are mainly in the vent. | Stays in the drain. |
| Obstructs air from getting in the washer. | Stops water from draining. |
| Causes are overheating. | It causes a prolonged cycle. |
#4. Too Many Error Codes on Display
Error codes arise from a series of malfunctions in your washing machine. First, you must observe and check the control panel for blinking lights.
However, if your Whirlpool washer has too many error codes simultaneously, it will beep until you fix it.
#5. Whirlpool Washer Needs a Reset
Once in a while, your Whirlpool washer will act up because it needs a reset. For instance, if your kid presses a bunch of buttons during the wash cycle, it will lead to a problem.
The reason is that the different commands that the washer receives are to facilitate specific actions. But, if there is a glitch, you need to reset it to restore it to default.
How Do I Fix a Whirlpool Washer That Beeps and won’t Start?
Fixing a Whirlpool dishwasher that beeps and won’t start is relatively easy. As long as you know the cause of the problem, you can fix it.
The previous subtopic highlighted a few probable causes of a beeping and unresponsive Whirlpool washer. Now, this section contains detailed steps to take to fix the problem.
Here are the following steps according to the malfunction.
#1. Partially-closed Door
If you encounter this problem, you have nothing to worry about. So far, it is one of the cheapest problems you can experience.
- Close the door properly.
- Remove any object that hinders the door from shutting correctly.
#2. Lint Build Up
If there is lint build-up, you must remove them from the vent. Follow these steps to do this:
- Locate the lint trap responsible for catching sneaky lint and remove it to clean it properly.
- The shreds on the lint trap would be unmistakable and irritating if you are sensitive.
- Next, remove the lint with your hands and use a brush for the smaller particles.
- To deep-clean the lint trap, leave it in hot water with a half cup of vinegar for a few minutes.
- Finally, take it out and rinse it under running water, and you can fix it back in the washer.
#3. Too Many Error Codes
If you notice the washer giving you a hard time, you can troubleshoot the washer. This way, you can ascertain the problem and solve it.
First, press three buttons on the panel and hold for three seconds. Ensure that the washer is running while you do this.
The error codes will pop, and you can fix the problem. First, however, ensure that you follow the manual.
#4. Clogged Drain
To clean the drain pump, you must follow these steps:
- First, please switch off the washing machine and unplug it.
- Next, stop the water supply by turning it off from the source.
- Next, disconnect all the pipes that are at the back to have access to the drain pump.
- Then, lay the washer on its back to reach the base, where the drain pump sits.
- Afterward, remove the wires that connect to it and loosen the screws that hold the pump.
- Finally, clean it with warm water and fix everything back in place.
#5. Whirlpool Washer Needs a Reset
To reset your Whirlpool washer, follow these steps:
- First, turn off the washing machine and disconnect it from the power source.
- Then wait for 30 seconds and plug it to power again.
- This action should reset it.
Why Is My Washing Machine Beeping When I Press Start?
If your washing machine beeps when you press start, it is about to begin the cycle. However, if it continues beeping, it indicates a fault.
Check if the door is shut and close it if it is not. This fault is usually the first that should come to mind.
On the other hand, it might be the drain pump or lint trap. Luckily, you can fix these problems quickly.
How Do I Stop My Whirlpool Washer from Beeping?
If you want your Whirlpool washer to stop beeping, you must fix the problem. But, first, troubleshoot the issue to find possible ways to solve it.
It is common for some malfunction; however, it should not be frequent. For example, check if the door is correct or the lights are blinking.
Blinking lights are the best indication of a problem with the washing machine. It would be best if you had your manual close each time.
This way, you can quickly check the problem while you troubleshoot it. However, you can call a technician if things get too complex for your understanding.
It would help if you cleaned your washer regularly. Then, you can include it in your plans or to-do list. For it to function well, ensure to clean it once every month.
You will be saving yourself unnecessary problems that come when you accumulate minor issues.
Final Thoughts
In conclusion, Whirlpool washers are prone to faults like every other washer. But, of course, you can fix them in a few steps.
You can fix it by resetting, cleaning the drain and lint trap, or ensuring that the door is not open. Finally, call a technician if you cannot handle it. I hope you find this helpful.
